8615824687445
sales@gneetube.com
enLanguage

ASME SA210 Grade C Seamless Tubes

Apr 02, 2024 Leave a message

ASME SA210 Grade C Seamless Medium-Carbon Steel Boiler and Superheater Tubes
SA-210C is ASME standard steel grade, which is medium carbon steel pipe for boiler and superheater pipe, pearlescent hot strong steel;
Applicable conditions: widely used in 300MW, 600MW and other large capacity power station boilers, heating surface piping and header, steam water piping, etc. with working temperature lower than 500 ℃, such as water wall, economizer, low-temperature superheater, etc.


ASTM A210 Grade C Seamless Boiler and Superheater Tubes
Manufacture:Seamless process ,Hot-finished or Cold-finished
Wall thickness(WT): 0.9 mm--12.7 mm.
Outer diameter (OD): 12.7 mm--127 mm
Length: 6M or specified length as required.
Ends: Plain End, Beveled End, Treaded

 

ASTM A210 Grade C Seamless Boiler and Superheater Tubes

OD (mm) Wall Thickness(mm)
  2 2.5 3 3.5 4 4.5 5 6 6.5-7 7.5-8 8.5-9 9.5-10 11 12
Φ25-Φ28 ● ● ● ● ● ●                
Φ32   ● ● ● ● ● ●              
Φ34-Φ36   ● ● ● ● ● ●              
Φ38   ● ● ● ● ● ●              
Φ40     ● ● ● ● ●              
Φ42     ● ● ● ● ●              
Φ45     ● ● ● ● ● ●            
Φ48-Φ60     ● ● ● ● ● ● ●          
Φ63.5       ● ● ● ● ● ● ●        
Φ68-Φ73         ● ● ● ● ● ●        
Φ76         ● ● ● ● ● ● ● ● ● ●
Φ80         ● ● ● ● ● ● ● ● ● ●
Φ83         ● ● ● ● ● ● ● ● ● ●
Φ89         ● ● ● ● ● ● ● ● ● ●
Φ95         ● ● ● ● ● ● ● ● ● ●
Φ102         ● ● ● ● ● ● ● ● ● ●
Φ108         ● ● ● ● ● ● ● ● ● ●
Φ114           ● ● ● ● ● ● ● ● ●
Φ121           ● ● ● ● ● ● ● ● ●
Φ127           ● ● ● ● ● ● ● ● ●

 

Mechanical Tests Required
(1)Tension Test-One tension test shall be made on a specimen for lots of not more than 50 tubes. Tension tests shall be made on specimens from two tubes for lots of more than 50 tubes .
(2)Flattening Test-One flattening test shall be made on specimens from each end of one finished tube from each lot.
(3)Flaring Test-One flaring test shall be made on speci- mens from each end of the one finished tube from each lot.
(4)Hardness Test-Brinell or Rockwell hardness tests shall be made on specimens from two tubes from each lot .
(5)Hydrostatic or Nondestructive Electric Test-Each tube shall be subjected to the hydrostatic.

ASME SA210 Grade C Seamless Tubes