Order at a Glance
| Products | Butt-weld fittings: 45° / 90° elbows, tees, concentric reducers |
| Standard | EN 10253-2:2016, Type B |
| Material | P355NL1 (1.0566) per EN 10028-3, normalized fine-grain steel |
| Pressure ratings | 30.0 MPa and 40.0 MPa (300 / 400 bar), as specified line by line |
| Sizes | OD 32, 57, 88.9 and 114 mm (EN outside-diameter series, approx. DN25–DN100); walls 6–12 mm |
| Quantity | 11 lines, 620 pieces |
| Low-temperature duty | Charpy V impact ≥ 40 J at −40 °C |
| Forming | Seamless, hot-formed (pressed/forged) fittings |
| Delivery | FCA (airport); quantity and range adjustable against final price |
| Exclusions from unit price | Packaging; black anti-corrosive coating |
| Published | 19 November 2026 |
Order Specification
| No. | Fitting | Size (OD × WT, mm) | Rating | Qty (pcs) |
|---|---|---|---|---|
| 1 | Elbow 45°, R=1.5D | 88.9 × 12 | PN 40.0 MPa | 40 |
| 2 | Elbow 90°, R=1.5D | 57 × 6 | PN 30.0 MPa | 180 |
| 3 | Elbow 90°, R=1.5D | 57 × 8 | PN 40.0 MPa | 10 |
| 4 | Elbow 90°, R=1.5D | 89 × 10 | PN 30.0 MPa | 60 |
| 5 | Elbow 90°, R=1.5D | 114 × 12 | PN 30.0 MPa | 60 |
| 6 | Tee | 32 × 6 | PN 40.0 MPa | 80 |
| 7 | Tee | 57 × 6 | PN 30.0 MPa | 60 |
| 8 | Tee | 89 × 10 | PN 30.0 MPa | 40 |
| 9 | Tee | 89 × 12 | PN 40.0 MPa | 30 |
| 10 | Reducer, concentric | 89 × 6 – 57 × 6 | PN 30.0 MPa | 30 |
| 11 | Reducer, concentric | 89 × 10 – 57 × 8 | PN 40.0 MPa | 30 |
| Total | 620 | |||
Material Requirements
| Property | Requirement | Basis |
|---|---|---|
| Tensile strength (Rm) | ≥ 490 MPa | EN 10028-3, P355NL1 |
| Yield strength (ReH) | ≥ 355 MPa | EN 10028-3, P355NL1 |
| Longitudinal elongation (A) | ≥ 22 % | EN 10028-3, P355NL1 |
| Impact energy (KV) at −40 °C | ≥ 40 J | EN 10028-3, P355NL1, longitudinal |
Every heat is tested against these four values, and the results appear on the EN 10204 3.1 certificate that travels with each line. P355NL1 is the low-temperature variant of the normalized fine-grain family: the −40 °C impact guarantee is part of the grade, not an add-on test negotiated later.
Type B: Wall Thickness At Bends And Branches
The order names Type B, and that single word decides the wall schedule. Under EN 10253-2, a Type A fitting carries the straight-pipe wall through the bend and branch; a Type B fitting carries increased wall in the bending and branch area so the fitting holds the stated operating pressure after forming thins the wall. On a 12 mm heavy-wall elbow the difference is measured in whole millimetres, not decimals. We quote and produce to the Type B wall schedule as written; substituting Type A equivalents is not an option on this order, and we do not price it that way.
Seamless, Hot-Formed, Stamped
All fittings are seamless: the body is hot-formed by pressing and forging from seamless tube, with no weld seam anywhere in the fitting. At 300 and 400 bar ratings that matters - a fitting body without a seam removes a whole inspection argument before it starts. Each fitting carries stamped marking (grade, heat, size, rating), so identity survives handling and the buyer's own coating process. The heavy lines - 88.9 × 12 and 114 × 12 elbows at R=1.5D - run on our hot-forming tooling for long-radius work, which is where thin-wall forming shops typically fall short on Type B walls.
FCA Airport Delivery And Price Exclusions
Handover is FCA at the airport: fittings fly, and 620 pieces of forged fittings are exactly the kind of cargo that moves by air when line pipe cannot. The buyer has set the quotation terms deliberately - packaging and the black anti-corrosive coating are excluded from the unit price - so bids are compared on the fitting alone, and the coating goes through the buyer's own process or a separate quote line. The order also states that quantities and the range can change against the price; we quote in tiers, so a volume move is a re-selection on the same price curve rather than a re-quotation from zero.
Packaging and shipping


Quoting EN 10253-2 Fittings?
Send the fitting table as it looks on your side - fitting type, OD × wall per line, rating and quantity, and the standard type (A or B) and material grade. Tell us the delivery term and coating basis, and we will quote line by line, with the certificate level stated, within 24 hours.

