ASTM A192 Heat Exchanger and Condenser Tubes: Chemistry and Properties

Nov 28, 2025 Leave a message

ASTM A192 Heat Exchanger and Condenser Tube Description

ASTM A192 and ASME A192 cover seamless carbon steel boiler tubes for high-pressure equipment under the American standard system. The tubes are used in heat exchangers, condensers, superheaters and similar equipment that transports high-temperature, high-pressure steam or hot water, which makes the grade a standard choice for the power and petrochemical industries.

The usual outside diameter range runs from 1/2 inch to 7 inches, or 12.7 mm to 177.8 mm, although other sizes can be produced as long as they meet the remaining requirements of the standard. Wall thickness is selected from the pressure design of the exchanger or boiler, so the tube is ordered as a diameter and wall thickness pair rather than as a single size.

Chemical Composition

Element A/SA 192
Carbon, C (%) 0.06 to 0.18
Manganese, Mn (%) 0.27 to 0.63
Phosphorus, P (%) 0.035 max
Sulfur, S (%) 0.035 max
Silicon, Si (%) 0.25 max

This is a low-carbon, fully killed composition. The restricted carbon range keeps the steel ductile enough for cold bending and tube rolling, while the controlled manganese range delivers the tensile and yield properties needed for internal pressure. Low phosphorus and sulfur residuals limit the risk of hot shortness and cold cracking during forming and welding of the tube to the tubesheet.

Mechanical Properties

Property A/SA 192
Tensile strength (MPa) 325 minimum
Yield strength (MPa) 180 minimum
Elongation (%) 35 minimum

The minimum elongation of 35 percent is the property that supports tube rolling, flaring and bending operations during exchanger fabrication. Because the allowable stress used in design is derived from these minimum values at the relevant temperature, the tube certificate and the design calculation must refer to the same specification year and the same grade designation.

Applications

Boiler heating surface components. A192 tube is widely used in key heating surface parts such as economisers, superheaters and reheaters of water-tube boilers at high pressure and above. These components are in direct contact with high-temperature, high-pressure water or steam, and the high-temperature strength and corrosion resistance of the grade suit this duty.

Industrial high-temperature equipment. In equipment with demanding high-temperature and high-pressure conditions, such as chemical reactors and petroleum refining units, A192 tube is used as a key piping material for transporting hot fluids under pressure, supporting safe and efficient operation of the plant.

Power plant condensers: shell and tube condensers where steam is condensed on the tube outside surface.

Feedwater heaters: multi-stage heaters in the boiler feed train.

Process heat exchangers: refinery and chemical plant exchangers handling hot process streams.

Superheater and reheater tubing: heating surface elements exposed to steam at pressure.

Selection Points for Exchanger and Condenser Service

Temperature: the grade is a carbon steel, so it is selected for moderate metal temperatures and is replaced by alloy grades where temperature rises further.

Wall thickness: determined by the design pressure plus the corrosion allowance required by the service fluid.

Tube length and bundle layout: fixed by the exchanger thermal design and the tubesheet pattern.

End preparation: plain, beveled or threaded ends, chosen to match the welding or rolling method used at the tubesheet.

Test and inspection: hydrostatic or eddy current testing, plus visual and dimensional checks, before the tube is accepted for the bundle.

Corrosion allowance is the decisive factor in many condenser projects, because wall loss on the cooling-water side sets the tube life. Where the cooling water is aggressive, either a thicker wall or a different grade is specified rather than the standard minimum wall.

Test, Inspection, Packing and Shipping

Tubes are inspected for dimensions, surface condition and mechanical properties, and pressure or non-destructive testing is carried out as required by the order. Tubes are then bundled, with end protection where necessary, and packed in wooden cases or other seaworthy packing so that the ends and the surface finish arrive undamaged. Marking follows the heat number and the specification so that the mill certificate can be traced back to each bundle on site.

FAQ

Q: What is ASTM A192 tube used for?
A192 seamless carbon steel tube is used for high-pressure boiler and heat transfer service, including heat exchangers, condensers, economisers, superheaters and reheaters.

Q: What is the outside diameter range of A192 tube?
The common range is 1/2 inch to 7 inches, or 12.7 mm to 177.8 mm, and other sizes can be supplied when the remaining requirements of the standard are met.

Q: What are the mechanical properties of A192?
Minimum tensile strength is 325 MPa, minimum yield strength is 180 MPa and minimum elongation is 35 percent.

Q: What is the chemical composition of A192?
Carbon 0.06 to 0.18 percent, manganese 0.27 to 0.63 percent, phosphorus 0.035 percent max, sulfur 0.035 percent max and silicon 0.25 percent max.

Q: Is A192 the same as A192 boiler tube and A192 heat exchanger tube?
Yes. ASTM A192 and ASME A192 refer to the same seamless carbon steel tube grade, and the same product is supplied for boiler, superheater, heat exchanger and condenser service.

Q: How is A192 tube tested and packed?
Tubes are dimensionally and visually inspected, with pressure or non-destructive testing as specified, then bundled with end protection and packed in wooden cases or other seaworthy packing.