API 5DP Drill Pipe Specification: PSL Levels, Grades and Dimensions

Mar 26, 2024 Leave a message

What API 5DP Covers

API 5DP is the specification that governs the delivery of steel drill pipe for oil and gas drilling and production operations. It applies to pipe with a thickened end (upset) and to drill pipe that is butt-welded or friction-welded to tool joints, and it defines three product specification levels: PSL-1, PSL-2 and PSL-3. The standard fixes the dimensional requirements, the steel grades, the mechanical properties, the inspection and testing regime and the marking of each joint. Understanding the structure of the standard is essential before placing an order, because a drill string ordered to PSL-1 and one ordered to PSL-3 differ not only in price but also in the amount of non-destructive testing and documentation that accompanies each joint.

Product Specification Levels

Level Typical scope Testing emphasis
PSL-1 Standard dimensional and grade requirements, general drilling duty Dimensional checks, hydrostatic test, grade verification
PSL-2 Additional mandatory requirements on chemistry and heat treatment Added non-destructive examination and impact testing
PSL-3 Most demanding level, critical and high-load wells Full non-destructive examination of body and tool joint, stricter documentation

Daily drilling practice usually selects PSL-1 for routine development wells and moves to PSL-2 or PSL-3 where the string will see high torque, deep or highly deviated trajectories, or where an H2S-containing environment requires traceability of every joint. The purchasing document must state the PSL explicitly, because the three levels are not interchangeable.

Dimensions, Length Ranges and Wall Thickness

Drill pipe is characterised by a thin wall and a low mass per unit length; its job is to provide a mud channel and to transmit tension and torque from the surface to the bit. Common outside diameters include 2 3/8 in, 2 7/8 in, 3 1/2 in, 4 in, 4 1/2 in, 5 in and 5 1/2 in. Wall thickness and inside diameter are matched to the required hydraulic performance and to the tensile load of the string. API 5DP defines three length ranges, which must be stated in the order together with the permitted length variation.

Length range Nominal length Typical application
Range 1 About 6.1 to 7.0 m (20 to 23 ft) Short assemblies, directional work
Range 2 About 8.2 to 9.1 m (27 to 30 ft) Most land and offshore strings
Range 3 About 11.6 to 13.7 m (38 to 45 ft) Deep wells, fewer make-up operations

The length mix in a string is normally selected so that the total length falls within the planned hole depth without an excessive number of short joints, and so that the handling equipment on the rig can accommodate the longest joint.

Upset Configuration and Tool Joints

The ends of the pipe body are thickened by an upset operation to compensate for the material removed when the tool joint thread is cut. Three configurations are used: internal upset (IU), external upset (EU) and internal-external upset (IEU). The upset type affects the inside diameter at the ends, the hydraulic performance and the fatigue behaviour of the joint.

Tool joints are threaded connectors welded to the pipe body, and they are manufactured in accordance with the same specification. Common connection sizes in use today include NC26, NC31, NC38, NC40, NC46, NC50 and NC56, where the number refers to the nominal thread size. Rotary shouldered connections must be matched to the pipe body diameter so that the joint outside diameter and the tool joint bore are compatible with the well programme. Hardbanding, when specified, is applied to the tool joint box and pin to reduce wear in casing, and the grade of hardbanding should be agreed with the operator because casing-friendly grades protect the intermediate casing string.

Steel Grades and Mechanical Properties

API 5DP drill pipe grades are designated by their minimum yield strength in ksi. The four grades most frequently ordered are E75, X95, G105 and S135. Higher grade means greater tensile and torsional capacity, but also lower toughness margin, so the grade must be selected together with the PSL and the expected load spectrum.

Grade Minimum yield strength Yield strength range Minimum tensile strength
E75 75 000 psi (517 MPa) 75 000 to 105 000 psi 100 000 psi (689 MPa)
X95 95 000 psi (655 MPa) 95 000 to 125 000 psi 105 000 psi (724 MPa)
G105 105 000 psi (724 MPa) 105 000 to 135 000 psi 115 000 psi (793 MPa)
S135 135 000 psi (931 MPa) 135 000 to 165 000 psi 145 000 psi (1 000 MPa)

Chemistry and heat treatment requirements become progressively stricter from PSL-1 to PSL-3, and the carbon, manganese and alloying element limits must be met for the specified level. Impact testing, hardness limits on the tool joint and non-destructive examination of the weld area are specified in the standard and are the reason why the delivered documentation of a PSL-3 string is far more extensive. Designations used by some domestic mills, such as R780, should always be verified against the ordered API grade on the mill certificate before the joint enters the string.

Ordering, Inspection and Marking

State the standard, the PSL, the outside diameter, wall thickness and length range for every item.

State the steel grade and the upset type, and the tool joint connection size and hardbanding requirement.

Require the mill certificate, the non-destructive examination report and the hydrostatic test record.

Confirm that stencilled marking on each joint matches the certificate before the joint is run.

Verify thread gauging and make-up torque data before the first joint is made up on the rig floor.

Correct inspection at the yard is far cheaper than a failed joint at depth. Recording the serial number, grade, length and tool joint condition of every joint in the string book provides the traceability that later failure analysis depends on.

FAQ

Q: What does PSL mean in API 5DP?
PSL stands for product specification level; API 5DP defines PSL-1, PSL-2 and PSL-3 with progressively stricter chemistry, testing and documentation requirements.

Q: Which drill pipe grades are most common?
E75, X95, G105 and S135; the number indicates the minimum yield strength in ksi, and higher grades give more tensile and torsional capacity.

Q: What length ranges does API 5DP define?
Range 1 of about 6.1 to 7.0 m, Range 2 of about 8.2 to 9.1 m and Range 3 of about 11.6 to 13.7 m, each with a permitted length variation.

Q: What is the difference between IU, EU and IEU upset?
They describe where the pipe end is thickened: internally, externally or both, which changes the end inside diameter and the hydraulic performance of the joint.

Q: How are drill pipe tool joints specified?
By connection size such as NC26, NC31, NC38, NC40, NC46, NC50 or NC56, matched to the pipe body diameter, with the hardbanding grade agreed for casing protection.

Q: Why is PSL-3 ordered instead of PSL-1?
For critical, deep or high-torque wells where full non-destructive examination and complete traceability of every joint are required.