Scope of ASTM A192 and ASME SA192
ASTM A192 covers seamless carbon steel boiler and superheater tubes with minimum wall thickness for high-pressure service. The grade is dual-listed as ASME SA192, so tube produced to either designation can be used in boiler construction governed by the ASME Boiler and Pressure Vessel Code. Because ordering practice is based on minimum wall thickness, the mill supplies a wall close to the calculated pressure-retaining requirement rather than a nominal schedule, which controls both weight and cost on large heating surfaces.
Tubes are produced seamless by hot working and, where required, cold drawn to final size, then heat treated, straightened and cut to length. Each lot is accepted on the basis of a hydrostatic test or an alternative nondestructive electric test, while flattening, flaring and hardness checks may be added at the purchaser's option.
Grade and Service Conditions
A192 is a single-grade specification. It is commonly applied to heating surface tubes, headers, economizers, superheaters and reheaters of high-pressure boilers, with working pressure generally not greater than 9.8 MPa and working temperature between 450 ℃ and 650 ℃. As a low-carbon, unalloyed grade it is not intended for the creep regime where chromium-molybdenum grades such as ASTM A213 T11 or ASTM A335 P22 are specified.
Chemical Composition
| Element | ASTM A192 / ASME SA192 |
|---|---|
| Carbon, C | 0.06 – 0.18 % |
| Silicon, Si | 0.25 % max |
| Manganese, Mn | 0.27 – 0.63 % |
| Phosphorus, P | 0.035 % max |
| Sulfur, S | 0.035 % max |
| Chromium, Molybdenum, Copper, Nickel, Vanadium | Not specified, residual only |
The narrow manganese range and the low carbon level keep the steel soft enough for cold bending and tube-sheet expansion while still meeting the specified strength floor.
Mechanical Properties and Hardness
| Property | Requirement |
|---|---|
| Tensile strength, Rm | 325 MPa min |
| Yield strength, ReL | 180 MPa min |
| Elongation in 50 mm | 35 % min |
| Hardness, wall 5.1 mm and above | 137 HB max |
| Hardness, wall below 5.1 mm | 77 HRB max |
Hardness control is the practical quality gate for this grade. A tube that is too hard will resist expansion into the drum or header and is more likely to crack during bending, so Brinell testing is used for heavier walls and the Rockwell B scale for thin walls where a Brinell impression would be too large for the section.
Dimensional Tolerances
| Product form | Dimension range | Permissible variation |
|---|---|---|
| Hot finished, outside diameter | Up to 101.6 mm | +0.4 / −0.8 mm |
| Hot finished, outside diameter | Above 101.6 up to 168.3 mm | +0.4 / −1.2 mm |
| Hot finished, wall thickness | 76 – 168.3 mm OD | +28 % / 0 |
| Cold drawn, outside diameter | Up to 25.4 mm | ±0.10 mm |
| Cold drawn, outside diameter | 25.4 – 38.1 mm | ±0.15 mm |
| Cold drawn, outside diameter | Above 38.1 mm | ±0.20 mm |
| Cold drawn, wall thickness | 38.1 mm OD and below | +20 % / 0 |
| Cold drawn, wall thickness | Above 38.1 mm OD | +22 % / 0 |
Length tolerance, square cut and straightness limits are agreed at the time of ordering, since minimum-wall tube is often supplied in exact cut lengths for a specific boiler bank.
Applications
Water wall and furnace heating surface tubes in industrial and utility boilers.
Economizer and superheater elements, plus reheater tubing.
Headers and connecting piping within the pressure limit of the grade.
Heat exchanger tube where a low-carbon, weldable and readily expanded material is acceptable.
For any of these duties the two governing selection criteria are the flue-gas side metal temperature and the internal pressure, matched against the allowable stress table of the code used for the design.
FAQ
Q: What is the difference between ASTM A192 and ASME SA192?
A192 is the ASTM designation and SA192 is the ASME code case of the same specification. Chemical limits, mechanical properties and tolerances are identical, so the two may be treated as one grade for boiler design.
Q: What is the maximum working temperature for A192 boiler tube?
The grade is normally used in high-pressure boilers with working temperature between 450 ℃ and 650 ℃ and working pressure generally not greater than 9.8 MPa. Above that range an alloy steel grade is selected.
Q: Why is hardness specified instead of only tensile strength?
Hardness governs formability, bending and expansion behaviour. The specification caps hardness at 137 HB for walls of 5.1 mm and above and at 77 HRB for thinner walls.
Q: Which tests are performed on A192 tubes?
Every lot is accepted on a hydrostatic test or an alternative nondestructive electric test. Flattening, flaring, hardness and dimensional inspection may be required in addition, depending on the purchase order.
Q: Can A192 tube be welded?
Yes. The carbon content of 0.06 to 0.18 % and the low manganese level give good weldability with conventional carbon steel procedures, filler and preheat rules matched to wall thickness.
Q: How is the tube supplied in terms of ends and surface?
Tube is supplied with plain or beveled ends, mill varnish free unless requested, and with the surface condition agreed between mill and purchaser. Each bundle is marked with heat number for traceability.

