A179 Pipe vs GB 5310 Pipe: Key Differences

Mar 03, 2025 Leave a message

Overview of A179 and GB 5310

A179 and GB 5310 are seamless steel tube specifications with different purposes and regional origins. ASTM A179/A179M covers seamless cold-drawn low-carbon steel tubes for heat exchangers, condensers and similar heat transfer equipment. GB 5310 is the Chinese national standard for seamless steel tubes used in high-pressure boilers, covering carbon steel and low-alloy steel grades. The two standards are often mentioned together in projects that need both boiler and heat exchanger tubing, but they are not interchangeable.

Standards and Scope

Item ASTM A179 / SA-179 GB 5310
Standard origin USA (ASTM / ASME) China (GB)
Product type Seamless cold-drawn tubes Seamless tubes
Primary service Heat exchangers, condensers, coolers High-pressure boilers, superheaters, reheaters, steam mains
Typical grades One low-carbon steel grade 20G, 15CrMoG, 12Cr1MoVG, etc.
Size range Small diameters, typically up to 3 in OD Wide range up to large diameters

Grade Systems and Materials

A179 defines a single low-carbon steel composition with carbon 0.06-0.18% and manganese 0.27-0.63%, optimized for ductility, tube rolling and welding. GB 5310 defines multiple grades for different service temperatures: carbon steels such as 20G for moderate temperatures, and Cr-Mo or Cr-Mo-V alloy steels such as 15CrMoG and 12Cr1MoVG for higher temperatures and creep-resistant service. The grade choice in GB 5310 depends on the design temperature and pressure.

Manufacturing and Testing

A179 tubes are cold drawn from seamless hollows to achieve accurate dimensions and a smooth surface, then annealed and tested for tensile properties, flattening, flaring and pressure integrity. GB 5310 boiler tubes are hot finished or cold drawn, subjected to normalizing or other specified heat treatment, and verified by chemical analysis, tensile and impact testing, hydrostatic or nondestructive testing, and surface and dimensional inspection. The testing and documentation requirements are typically more demanding for boiler tubes because of the severe service conditions.

Applications

A179 tubes are installed in shell-and-tube heat exchangers, condensers and coolers in refineries, power plants and process plants. GB 5310 tubes are used in boiler water-wall, superheater, reheater and main steam systems, as well as in high-temperature steam pipelines. A project may require both: A179 for the heat exchange bundles and GB 5310 for the boiler pressure parts.

How to Choose

Select by the component function: use A179/SA-179 for heat exchanger and condenser tubes, and GB 5310 for boiler and high-pressure steam tubes. Also consider the governing code of the project, the design temperature, and the required inspection documents. Confirm the exact grade, size, heat treatment and test requirements with the tubing supplier before ordering.

FAQ About A179 and GB 5310

Can A179 tube be used in a boiler?

Not for high-pressure boiler pressure parts. A179 is designed for heat exchanger service, not for boiler steam generation duty; boiler tubes must follow standards such as GB 5310 or an equivalent boiler tube standard.

Is GB 5310 only for carbon steel?

No. GB 5310 covers both carbon steel grades such as 20G and alloy steel grades such as 15CrMoG and 12Cr1MoVG.

What is the main difference between the two standards?

The main difference is the purpose: A179 is a heat exchanger tube specification, while GB 5310 is a boiler tube specification for high-pressure steam service with different grades and more demanding testing.

Does GB 5310 use the same grade system as A179?

No. A179 uses a single ASTM composition; GB 5310 uses Chinese grade designations such as 20G and 12Cr1MoVG.

Which standard should be used for a superheater tube?

For superheater and reheater service, use a boiler tube standard such as GB 5310 (for example 15CrMoG or 12Cr1MoVG) or the equivalent international boiler tube standard required by the project.

Can the two types of tubing be welded together?

Yes, with proper welding procedures, since both are carbon or low-alloy steels; filler metal and preheat should be selected for the higher-strength grade.