S355JR Steel Tube Properties: EN 10025-2 Grade Explained

Dec 26, 2025 Leave a message

What S355JR Steel Tube Means

S355JR is a hot-rolled structural steel grade defined by EN 10025-2, and the same designation is applied to tube, hollow section and plate products. The name carries the full specification: S stands for structural steel, 355 is the minimum yield strength in MPa for the thinnest sections, J indicates a Charpy V-notch impact energy of 27 J, and R shows that the impact test is carried out at room temperature, 20 °C. Tube made from this grade is normally supplied in the as-rolled condition, and a different delivery condition can be agreed when a project requires it.

Although the grade began as a plate and section material, square, rectangular and circular tube in S355JR has become common because a hollow section delivers stiffness with a low self-weight. The result is efficient for frames, supports and structures where a solid section of equal capacity would be far heavier.

Chemical Composition of S355JR

The chemistry is deliberately simple. S355JR is a carbon-manganese steel with no intentional alloy addition, and the limits of EN 10025-2 keep carbon low so that strength comes from a fine ferrite-pearlite structure rather than from alloying.

Element Max (%) Role
C 0.24 Limits hardening in the weld heat-affected zone
Si 0.55 Deoxidation
Mn 1.60 Deoxidation, grain refinement, strengthening
P 0.035 Impurity, controlled for toughness
S 0.035 Impurity, controlled for toughness
Cu 0.55 Residual; a modest addition improves atmospheric corrosion behaviour

Residual elements are capped because they raise hardness and reduce toughness in the heat-affected zone of a weld. Copper is the exception in practice: a small amount left in the steel is one reason S355JR tube performs slightly better than plain carbon steel outdoors.

Mechanical Properties and Wall Thickness

Yield strength is thickness dependent. A heavy wall cools more slowly after rolling and develops a coarser microstructure, so the standard steps the minimum value down as thickness rises. Tensile strength follows the same logic, with a wider band permitted for very thick product.

Wall or plate thickness (mm) Minimum yield strength (MPa)
≤ 16 355
16 – 40 345
40 – 63 335
63 – 80 325
80 – 100 315
100 – 150 295
150 – 200 285
200 – 250 275
Property Value
Tensile strength (up to 100 mm) 470 – 630 MPa
Tensile strength (over 100 mm) 450 – 600 MPa
Elongation (3 – 40 mm) ≥ 22 %
Charpy V-notch impact, JR quality 27 J at 20 °C

Why S355JR Tube Performs Well in Service

Strength with toughness: the grade holds a high yield strength while retaining enough impact resistance for dynamic or shock loading.

Weldability: the carbon equivalent is low enough that the material is not prone to cold cracking under normal fabrication procedures, so it suits structures assembled largely by welding.

Weather resistance: atmospheric corrosion behaviour is slightly better than that of ordinary carbon steel, which makes the grade practical for unprotected outdoor frames.

Forming flexibility: the steel can be cut, bent and formed in the shop without special tooling.

S355JR is nevertheless a general structural grade rather than a specialised one. For service at very low temperature or in highly aggressive environments, higher-toughness quality classes such as J0 or J2, or additional surface protection, are the appropriate answer.

How Tube Is Produced and Specified

Hot-rolled strip is formed into shape and welded along the seam, or a seamless route is used when a project calls for it. Because S355JR is specified through EN 10025-2, the mechanical requirements are attached to the steel, while the dimensional requirements of the tube itself come from the hollow section or tube standard named in the purchase order. Wall thickness, corner radius, straightness and length tolerances all depend on that product standard, which is why tube size and wall thickness must be confirmed against the actual design requirement before an order is placed.

Typical Applications

Factory supports, roof purlins and crane runway brackets

Stair stringers, handrails and canopy frames

Equipment frames, machine bases and conveyor support structures

General infrastructure such as towers, trestles and non-critical bridge members

Trailer and agricultural machinery chassis where strength-to-weight ratio matters

Frequently Asked Questions

Q: What does S355JR mean?
S denotes structural steel, 355 is the minimum yield strength in MPa, J is a 27 J Charpy V-notch energy requirement and R means the impact test is performed at room temperature.

Q: What is the tensile strength of S355JR?
The standard band is 470 to 630 MPa for product up to 100 mm thick, and 450 to 600 MPa above that thickness.

Q: Why does the minimum yield strength fall with thickness?
Thicker material cools more slowly and develops a coarser grain structure, so the standard reduces the required minimum from 355 MPa at 16 mm and below to 275 MPa at 200 to 250 mm.

Q: Is S355JR steel tube suitable for outdoor use?
Yes. Its atmospheric corrosion resistance is slightly better than that of plain carbon steel, though painting or galvanising is still usual for long service life.

Q: Can S355JR be welded without preheating?
In most cases the low carbon equivalent permits welding without preheating; heavy walls, high restraint or low ambient temperature may still require a qualified procedure with preheat.

Q: When should a higher quality class be chosen instead?
When the structure must resist impact at low temperature or works in a corrosive environment, the J0 or J2 classes or an additional protective system are more appropriate than the basic JR grade.