Reading the S355JR Designation
Every letter and number in S355JR answers a question about the material. S identifies a structural steel intended for load-bearing use. 355 is the minimum yield strength in MPa, meaning the steel only begins to deform irreversibly when the stress reaches that level, well above ordinary S235 carbon steel, which is why thinner members can carry the same load. J indicates that the steel must absorb a defined amount of energy in a Charpy V-notch impact test, and R shows that the impact test is performed on the as-rolled product at room temperature, 20 °C.
Taken together, the designation describes a hot-rolled, weldable, medium-strength structural steel. It does not promise low-temperature toughness, corrosion resistance or elevated-temperature strength; those needs are met by other quality classes or other steel families, and selecting the grade without that distinction is the most common specification error.
Chemical Composition of S355JR Structural Tube
The composition below follows EN 10025-2 for the JR quality class. Limits are maxima in percent by mass, and the balance of the analysis is iron with residual elements kept low in a controlled steelmaking practice.
| Element | Max (%) | Purpose |
|---|---|---|
| C | 0.24 | Strength and weldability balance |
| Si | 0.55 | Deoxidation during steelmaking |
| Mn | 1.60 | Deoxidation, grain refinement, strength |
| P | 0.035 | Impurity; kept low against brittle fracture |
| S | 0.035 | Impurity; kept low against brittle fracture |
| Cu | 0.55 | Residual, with a mild effect on corrosion behaviour |
Alloy content is minimal by design. Strength in S355JR comes from manganese, from grain refinement and from controlled rolling rather than from costly alloying elements, and the low carbon level is what keeps the material weldable in the shop without complex procedures.
Mechanical Properties of S355JR Tube
| Property | Value |
|---|---|
| Minimum yield strength (thickness ≤ 16 mm) | 355 MPa |
| Measured yield strength in normal production | 355 – 400 MPa |
| Tensile strength | 470 – 630 MPa |
| Elongation | ≈ 22 % |
| Charpy V-notch impact, JR quality | 27 J at 20 °C |
The ductility expressed by that elongation figure is what allows tube to be bent, cut and formed without cracking, and it also gives a structure a reserve of deformation before failure. The minimum yield strength always applies: measured values for structural tube in normal production sit between 355 and 400 MPa, comfortably above the grade minimum.
Hardness, Weldability and Machinability
Hot-rolled structural tube of this grade typically shows a hardness in the region of 70 to 80 on the Rockwell B scale, which corresponds to good wear behaviour in general structural service without being difficult to machine. Weldability is one of the grade's main advantages: manual arc, submerged arc and gas-shielded processes are all used successfully, and because carbon and the carbon equivalent are low, the material resists cold cracking and gives designers freedom in joint detailing. Cold working such as cutting, bending and punching is straightforward, and hot working operations such as forming are equally practical.
Comparing the S355 Impact Quality Classes
The letter after J is the key to service temperature, and it is the detail most often confused. In the JR grade the impact test is carried out at room temperature. Where a project specifies impact testing at a lower temperature, the J0 class requires 27 J at 0 °C, the J2 class requires 27 J at minus 20 °C, and the K2 class requires the higher energy of 40 J at minus 20 °C. Choosing the class is a design decision based on the lowest expected service temperature, the consequence of brittle failure and the requirement of the applicable code.
Applications and Selection Notes
Building frames, column bases and bracing where the 355 MPa strength class suits a medium to heavy load
Machine frames, equipment skids and conveyor structures that benefit from a hollow section's stiffness
Infrastructure elements such as towers, walkways and non-critical bridge members
Vehicle, trailer and agricultural machinery structures, where strength-to-weight ratio governs the design
Because tube dimensions are governed by the product standard named in the order while the material requirements come from EN 10025-2, the size and wall thickness must always be matched to the calculated load and deflection limits rather than selected from a catalogue alone.
Frequently Asked Questions
Q: What is the maximum carbon content of S355JR?
The heat analysis permits up to 0.24 % carbon, a level that keeps the steel weldable while allowing the required strength.
Q: At what temperature is S355JR impact tested?
The JR quality class is tested at room temperature, 20 °C, with a minimum Charpy V-notch energy of 27 J.
Q: Is 0 °C impact testing covered by the JR suffix?
No. Impact testing at 0 °C belongs to the J0 class, and testing at minus 20 °C belongs to the J2 class at 27 J or the K2 class at 40 J.
Q: Does S355JR tube contain alloying elements?
No deliberate alloy additions are made. Strength comes from carbon, manganese, grain refinement and controlled rolling, with copper and other residuals limited by the standard.
Q: How hard is S355JR structural tube?
As-rolled tube of this grade usually measures around 70 to 80 HRB, which suits general structural duty and remains easy to machine and fabricate.
Q: What elongation can be expected?
Approximately 22 %, which gives enough ductility for cold bending, forming and, in a finished structure, plastic redistribution of load.

