What Is ASTM A179 Material?
ASTM A179 is the specification for seamless cold-drawn low-carbon steel tubes of minimum wall thickness for tubular heat exchangers, condensers and similar heat-transfer equipment. The material is selected for these duties because cold drawing produces the tight dimensional tolerances and smooth surfaces required for tube-to-tubesheet joints, while the low carbon content keeps the tube ductile and weldable. The specification is also published as ASME SA179 for use under the boiler and pressure vessel code.
Chemical Composition
| Composition | Min (%) | Max (%) |
|---|---|---|
| Carbon (C) | 0.06 | 0.18 |
| Manganese (Mn) | 0.27 | 0.63 |
| Phosphorus (P) | - | 0.035 |
| Sulfur (S) | - | 0.035 |
The low carbon and tight phosphorus and sulfur limits keep the steel clean and ductile, which is essential for bending, flaring and rolling the tube ends into tube sheets.
Mechanical Properties
| Property | Requirement |
|---|---|
| Tensile strength | 325 MPa min |
| Yield point | 180 MPa min |
| Elongation | 35% min |
The minimum elongation of 35% reflects the ductility needed to expand and roll tube ends without cracking, a standard operation when assembling heat exchangers.
Size Range and Unit Requirements
The standard applies to tubes with outside diameters from 1/8 inch to 3 inches, which is 3.2 mm to 76.2 mm. A steel tube with an outside diameter and wall thickness smaller than this range is also covered by the standard, but the relevant mechanical properties do not apply to outside diameters below 1/8 inch (3.2 mm) or wall thicknesses below 0.015 inch (0.4 mm).
The specification provides values in both inch-pound and SI units, with SI values in parentheses. The two systems of units do not agree precisely and cannot be used at the same time. When the inch-pound system is used, the use of SI units must be specifically stated in the order so that testing and acceptance are not confused.
Manufacturing and Heat Treatment
A179 tubes are produced by cold drawing from hot-finished tubular rounds, then heat treated to restore ductility and stabilize the mechanical properties. The standard delivery condition is annealed, which gives the tube the fine grain and uniform properties needed for heat-transfer service. The finished tube is tested for pressure integrity and checked for dimensions before shipment.
Applications and Selection Points
Heat exchangers, condensers and similar heat-transfer equipment in refineries, chemical plants, power stations and HVAC systems.
For higher temperatures or alloy requirements, select A213 tubes instead; A179 is a low-carbon carbon steel grade for moderate service.
Specify the exact OD, wall thickness or minimum wall, length, and unit system when ordering, and confirm the test requirements with the project specification.
Common Misconceptions
A179 is not a pipe specification for general piping. It is a tube specification for heat-transfer equipment with minimum-wall condition and tube-specific tolerances.
Cold-drawn does not mean hard and brittle. The annealed delivery condition restores the ductility required for rolling and expanding.
The composition is not fixed to one point. Values are ranges, and a heat may differ within the limits while remaining compliant.
A179 and A106 are not the same product. A106 is a seamless carbon steel pipe for high-temperature service in larger sizes; A179 is a small-diameter cold-drawn tube for heat exchangers.
FAQ
What is ASTM A179 material?
ASTM A179 is the specification for seamless cold-drawn low-carbon steel tubes of minimum wall thickness used in tubular heat exchangers, condensers and similar heat-transfer equipment.
What is the chemical composition of A179?
Carbon is 0.06% to 0.18%, manganese is 0.27% to 0.63%, and phosphorus and sulfur are each limited to 0.035% maximum.
What are the mechanical properties of A179 tubes?
Minimum tensile strength is 325 MPa, minimum yield point is 180 MPa, and minimum elongation is 35%.
What size range does ASTM A179 cover?
The standard covers tubes with outside diameters from 1/8 inch to 3 inches, which is 3.2 mm to 76.2 mm, with smaller tubes covered by a note excluding the mechanical property requirements below the minimum sizes.
What is the difference between A179 and A106?
A106 is a seamless carbon steel pipe specification for high-temperature service with larger sizes and heavier walls, while A179 is a small-diameter cold-drawn tube specification for heat exchangers and condensers.
Why is A179 delivered annealed?
Annealing after cold drawing restores ductility, refines the grain and stabilizes the mechanical properties, so the tube can be rolled, expanded and flared during exchanger assembly without cracking.

